Euro-Reef In-Sump Skimmer model CS12-2.
Includes Bubble Blaster HY-3000S pump. Also includes Euro-Reef Gate Valve Outlet Assembly 1-1/2″.
This awesome skimmer just looks impressive. We used it for 2-3 years before upgrading to this new pump in preparation to use it on our 315g dream tank. This pump has only has about 2 months use before we tore down the tank. We used it on our 220g tank which was VERY heavily loaded w/ SPS and it worked extremely well! Wholesale was $820 – without the pump. All equipment is in great shape!
Specifications: Height: 30″ Base: 17″ x 24″ Diameter: 12″ Recommended Tank Size: 500+ gal. You will need to have at least a 24″ wide sump for this skimmer to sit in.
Euro-Reef RS-80 Skimmer is in great condition. We loved this skimmer. It’s a great size, easy to set up and easy to maintain. It has a fitting to drain skimmate to a separate container (we used a 2 liter bottle). It’s rated for a much larger tank, but we successfully used it on our 120g cube tank reef FULL of SPS corals. Would work great for smaller tanks also. Pump shown is not included.
Sulphur Nitrate reactor custom built by David’s Reef. Works well, looks nearly new. Includes 1+ bags of new sulphur pellets. This is a really nice reactor, not just limited to using sulphur. Sulphur can help to keep your nitrates down. I have been known to overfeed my fish and corals, so this really helped out by limiting algae growth.
1 used Eheim #1250 pump. We just checked it and it’s still running great.
The pump on the right is sold.
The plastic housing on the left pump has a chipped off piece on the housing, but it doesn’t impact performance. I believe you can still get replacement needle wheel parts.
Used Marineland NJ3000 Pump. This is the Italian made model, the better design. Slightly used, but still works great!
Marineland NJ1800 Pump
This is a used Marineland pump. It’s the Italian made model which is the better design. In good shape.
System engineered to automatically top off water in your aquarium from a remote tank source of saltwater. It uses a Bulk Reef Supply peristalic pump and a water supply plumbed and wired to the sump with a float switch. It features flashing LED indicators during operation at both the remote tank and display tank, along with power outlets to control additional pumps that may be used during water changes. Sump float switch is mounted on a magnet to easily adjust the water level. It works great! Very reliable! It has saved us from lots of what would have otherwise been disasters.
Parts include: Bulk Reef Supply peristalic pump Model MP2-B.
Watch the video below to see how it works (download it first).
This is a system to make small water changes each day using pre-mixed saltwater. It prepares the saltwater, stores it, and dispenses small water changes as specified. It’s operation is based on a Stenner MP1004 dosing pump. Includes two blue tanks, one for RO storage, one for saltwater mix. Both have individual float switches and controls to integrate to a reef controller. (We used a ReefKeeper Elite controller – also for sale separately.) Saltwater mixing tank uses a Custom Sea Life Titanium Velocity T4 pump.
NEW Clear acrylic cylinders – great for DIY projects such as media reactors or skimmers. Most are still wrapped in plastic. Size: 14″ H x 6″ OD diameter. 1/8″ thick acrylic. There are several available. With shipping, these will run $25 ea.
250w metal halide ballast. We have always loved metal halides to get the very best fast growth and color out of SPS corals for coral farming. We used to run them on all our SPS tanks. LED lights are nice, but they don’t really compare.
Note: The reflector in the picture on the right was sold separately.
All the ballast parts fit inside the blue ballast box. Heavy blue metal base on this ballast. Very limited use.
This is a great little reactor to put in the sump in a high-flow area. We used to run carbon in it, but it could be used for various other types of media. Both ends unscrew so it’s easy to clean and change out.
UPDATE – 2/10/2020
Our dream tank has a new home! Congratulations to Dylan in Hobe Sound. It will be the focus of his garage remodel project to create a Man Cave
This is a detailed description of the tank and stand
Below is the specifications of the system followed by a Build Blog including every detail of the construction as it was built.
- Rimless peninsula build
- Dimensions: 7′ x 3′, 24″ tall, rimless. Top rim is 54″ from the floor
- Capacity: 315 gallons
- Weight: 700 lbs.
- Material: 3/4″ low iron Diamant glass- 3 sides
- Overflow: Internal glass with acrylic weir, Bean Animal drain
- Built by Reef Savvy
The design of this tank offers a 270 degree view of your reef tank for maximum viewing enjoyment. It was custom built by Felix of Reef Savvy, and in pristine condition.
- Material: 2 1/2″ x 3/16″ square steel and 3″ x 3 1/2 x 1/4″ angle
- Weight: 485 lbs (steel:345 lbs., wood trim 140 lbs.)
- Finish: White epoxy industrial finish
- Design: Robert Wright, structural engineer
- Fabrication by: David at Ultimate Motorsports
- Skinned with Angélique, a Brazilian teakwood supplied by Amazon Exotic Hardwoods.
- All of the doors are removable for sump access
Circulation and Sump
- PowerHeads: Vortech MP60, 2 ea. located on back wall
- Return pump: Set up for Water Blaster HY-7000 (not included), approximately 4x turnover (1200-1400 gallons/hour)
- Sump is 5′ long, 2′ wide and 16″ tall made of 3/8″ cast acrylic It features a large refugium area.
The system comes with an absolutely silent return overflow and water delivery system that delivers excellent water circulation throughout the tank. The drains are the “Bean Animal” design using three 1 1/2″ drains with gate valve regulation to match the delivery pump volume resulting in zero water bubbles throughout the 5′ long sump. The electrical outlets are wired on two 20 amp circuits providing 28 individual receptacles.
The tank was completed and filled in Mid June of 2012. We had it up and running for around two years.
One of the final pieces of equipment was a Vertex Libra dosing pump and vessels. It is very easy to set up and use.
Although it was set up and running, we only had an accumulated run time of 45 minutes.
Skimmer selection was a Deltec SC-2560 (now sold), the final piece of equipment
David’s Tanks and Innovations (DTI) is working on the custom sump. It will measure 5′ x 2′ x16″ and be constructed of 3/8″ acrylic.
There are two 20A isolated circuits to power the tank, with GFCI breakers installed in the panel. There are 28 individual power receptacles.
I will be using a Digital Aquatics Reefkeeper Elite to control some functions, so there are 2 PC-4 power units to provide eight controllable outlets. Cables will be managed by PVC wiring trough.
This shows assembly of the outlets, boxes and associated wiring.
All of the controllers, power transformers, etc. are attached to the stand with 2″white velcro tape. It allows easy maintenance access and flexible mounting arrangements.
This is a power outlet to make it convenient to plug in a pump, light or tool. The lower outlet is controlled by a relay that is wired to the water makeup float switch. This makes a safe and handy way to pump water into the tank when doing a water change.
The heaters are controlled by a Ranco commercial controller.
Vortech MP-60 pumps are installed on the back wall of the tank.
There is a pantry on the opposite side of the wall that allows me to install the dry side of the VorTechs through the wall.
Both pumps are accessable from the other side of the wall. This also isolates much of the noise these pumps are known for.
The VorTech controllers are attached behind the cabinet door with velcro.
The system is finally ready for a fresh water fill. Kind of a hold your breath moment, but all went well. I am very pleased with the overflow system. It is absolutely silent and there are no air bubbles entering the sump at all. This will not only eliminate noise, but stop the salt creep that is typical of sump areas. The VorTech pumps are very quiet, and are moving a lot of water.
The 3 drains are 1 1/2″ black PVC and the 2 returns are 1″ black PVC. The drain method used is known as the “Bean Animal”, named after the forum handle of the reefer that perfected the design. It consists of three drains, the one on the right (1) with a gate valve is a full siphon, meaning that is is adjusted to a point where no air is being drawn in with the water. The center drain (2), or clear channel has a small air vent installed on the top of the standpipe above it, allowing a small amount of excess water to drain without drawing much air into the water stream. The left drain (3) is an emergency overflow. It is installed so that it will handle all the water if necessary because of a blockage on the other two drains.
The left emergency overflow is open on the top while the other two look very much like a typical durso, except that the full siphon on the right has no air hole.
The airline tubing is fastened just above the water level so that if the water rises in the overflow box it will draw water and become a full siphon which handles much more volume. I will update this post later with some photos of the standpipes out of the tank.
Installing the bulkheads presented a challenge when it came to tightening the bulkhead nuts. With 1 1/2″ of foam and plywood between the tank bottom and the 1/4″ steel of the stand, it became impossible to tighten the nuts with regular tools.
I used a bandsaw to rough cut the jaws of a wrench.
After some filing and a little bit of help from Iggy and his welder, I now have two wrenches that will allow me to tighten or adjust the bulkhead nuts.
With the pump running, there are no bubbles being released into the sump. No air also means no noise.
The return pump is a Water Blaster HY-7000 by Reef Octopus. It is rated 88 watts 97% efficiency Max Flow=1800gph Max Head=12ft. Very quiet.
At last, the stand and woodworking is complete. I had a lot of people ask when there would be water in the tank, and as you can see there is indeed water in the tank.
The hinges are mounted to the stand with #8 stainless steel machine thread screws. They are spring closing hinges that act when the door is about 6″ open. They work nicely with standard magnetic latches without using the striker plate. The hinges also allow the door to be completely removed. Drilling and tapping 40 holes in 3/16″ steel was tedious.The hinges were given a coat of clear acrylic spray to help protect them from the salt environment.
Here is a view of the cabinet door edges. A groove was cut with the shaper on the edge to allow your fingertips to grip the door when it is against the magnetic catch.
The trim was attached with liquid nail adhesive. A bead of silicone was added on the top side to seal any water drips from the glass.
All of the doors can be opened for service. They also have removable hinges so the doors may be taken off.
The Angélique hardwood was supplied by Amazon Exotic Hardwoods, owned by fellow reefer James Lie. James has a tank of similar size for which he built a stand using Zebrawood.
The lumber is 10′ lengths of 6″ x 1″
A long time friend from my sailing buddies, Kenny Eads is a master cabinet builder and has a shop in Casselberry. He is my Jedi Master of woodworking, and allowing me to use his shop to build the cabinetry.
Here we have the boards cut to the cabinet door height.
Each cabinet door will have four boards glued together. Because the planer will not handle the width of the full door, I am gluing two boards which will be planed, then glued to the other half.
The two boards are now planed to a smooth surface.
Two sets are glued together for the full cabinet door width.
The door is now cut square with the side with a sliding jig on the table saw to make the corner a perfect 90° angle
The door is flipped over and trimmed to the exact width set by a stop block.
Hinges were mounted to the doors, then the hinge attachments ere made to the stand. Drilling and tapping 56 holes in 3/16″ and 1/4″ steel was quite tedious.
The stand looks much more finished with all the doors mounted. The corners and styles are not yet fitted.
Here we are sawing a board to be used for the trim between the tank and doors. We are using a bandsaw with a power feeder to yield two 3/8″ boards from one plank.
I ordered some 1″ and 1 1/2″ black PVC Plumbing parts for drains and returns.
I picked up the hardwood for the stand from James Lie at Amazon Exotic Hardwoods. The wood is Angelique, a South American import wood. It will take about 60 board feet to make the cabinet doors. I will be building the stand the week after Thanksgiving with the help of a cabinet builder and friend, Kenny Eads.
The tank has been completed and waiting at Reef Savvy for a number of months now, and the stand is finally ready. Chad Newman offered to take a day off and drive me down to Miami, and Al Schreiber came along for the ride. It was a good thing we had the help loading the tank at the Miami end. We had one end of the tank on a lift and it took everything all four of us could do to raise one end of the tank level with the pickup bed.
This 7 foot monster weighs 700 lbs. (The tank, not Felix)
We backed up to the front door at home, which shortened the distance for the carry significantly. We used a sheet of plywood and a sheet of 2″ foam to cushion the ride. Chad’s big duelie truck was the perfect ride for the trip (except for the amount of diesel we burned).
Here is the start of the lift. We have eight big boys here, and we needed every one of them!
Here we are almost in place. Watch the fingers!
What a relief to see the tank in its final resting place.
A real big thanks to the moving crew- Al Schreiber, Michael Harnett, James Goodyear, Iggy Galarza, Chad Newman, Ed Newman, David Hill, Rick Loewen (me), and Skippy Dooling.
There was some drywall work to be done before the stand was placed. Not shown are some holes in the wall to accommodate a pair of Vortec MP-60s. There will be holes in the back side of the wall in a pantry area to allow access to the Vortecs.
The stand was brush painted with Sherwin Williams MacroPoxy 2-part epoxy paint. It was very thick and difficult to apply smoothly. It took two coats to cover the bare metal. Next, a piece of 3/4″ plywood was cut to size and holes drilled for the 1 1/2″ drains and 1″ returns.
The wood was then coated with a coat of epoxy for waterproofing.
A piece of 3/4″ foam insulation was cut, similar to the plywood. This will be placed directly under the tank to provide a surface that will conform to irregularities.
MOVING THE STAND
I recruited a group of friends to help move the stand after a nearby ORCA club meeting. Pictured are Rick Loewen (me), Iggy Galarza, Mike Martin, Terry Alexander, James Goodyear and Al Schriber. The stand weights about 350 lbs., It easily took all of us to move the stand.
In the front door we come.
The stand is now in place. Note the leveling feet. They are industrial leveling feet with 1/2″ thread and a 2″ swivel pad.
Just got the tank stand back from the sandblaster. Nice and clean, ready to paint. It is very critical to keep it dry after they blast it with aluminum oxide to remove all of the scale and rust. Even the slightest amount of moisture will start it rusting. It was the perfect day to do the job with the humidity only at 35%, very unusual for Florida.
The stand is back from the welder. After a little clean-up, it will go to the sand blaster to prep it for paint.
The stand design was drawn by Robert Wright, a reefer in South Florida who is a structural engineer. The legs and crossbeams are 2 1/2″ x 3/16″ with 3 1/2″ x 3″ angle forming the top.
Leveling feet are tapped into a plate welded across the bottom of each leg.
The stand construction is finally underway! The design phase took a while, but we are in the fabrication phase now. I want to thank Robert Wright, a fellow reefer and steel fabrication engineer in south Florida for some incredible advice and design work on the stand. I purchased all of the steel needed, but cutting to exact lengths was going to add some significant expense to the project. With some borrowed industrial grade tools from local reefer friend Iggy, the steel is all cut to exact lengths and all that is left is some miscellaneous fabrication and trimming. The next step is getting it to over to Dave the welder, a guy that builds race cars, monster trucks and a lot of other neat stuff.
One of the challenges was to cut 32 5″ gussets. Gussets are triangular pieces of steel that are welded in the corners in order to reinforce the joints against lateral stresses. Using the bandsaw, a jig was made to hold the pieces at the correct angle to make the 45° cuts. There is a total of 346 lbs of steel.
Reef Savvy posted some Facebook pictures today of the completed tank. It will have to stay with Felix for a while while I get the stand construction underway. Terry says it is not coming into the house until it has a place to land. No moving it twice!
Felix at Reef Savvy has posted a photo of the new tank start on his facebook
315 gallon rimless penninsula iron-free glass tank
We needed a good visual to start getting used to what the new tank will look like. I built a mock up of plywood and acrylic so we can start getting used to the new monster in our living room.
New tank mock up – view from front door
New tank mock up – view from dining room
New tank mock up – view from living room
The area where the old tank came out is providing a challenge. I have a few spare floor tiles, but not enough to repair the area. Thinking ahead to a day when there would not be a tank here, it will just have to be replaced with another divider wall. The stand will have leveling feet, so the differences will be easy to deal with.
Removing the old tank
The 18-year old 79 gallon fish tank had to come out, and some structure along with it. It didn’t take long, but the refinishing looked like a challenge. Especially the ceiling, it would be nearly impossible to match the texture after it was patched. Then I got this brilliant idea that a return air grill will cover the patch and look way better than a repair.
Pictured here is our 18 year old FOWLR (Fish Only With Live Rock) tank before demolition. You can see some plywood and acrylic attached to the back side of the column, a mock-up to help visualize the size of the planned tank.
The column to the ceiling will be removed along with the wall section under the tank. The new tank will be located in the same area as the old one, but will be 7′ long (the distance from the column to the wall) and 3′ wide instead of the previous 12″. The new tank will be rimless with the lighting suspended from the ceiling with the lighting type yet undetermined.
This view from the dining room shows the butler’s pantry on the opposite side of the wall from the tank. There will be an access panel that will allow maintanence to the Vortec MP-60 circulation pumps.
This is a view from the back of the living room. I have constructed a temporary mock- up of plywood and acrylic to get an idea what the new monster will look like.